Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
This great article which follows relating to How to Install a Bathtub is fairly enlightening. Read it yourself and decide what you think of it.
Installing a bathtub isn't precisely rocket science, but it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult project. If the old tub is readily available, the job can relocate immediately; if you need to open up a wall to remove the old tub as well as position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly aid you mount a brand-new bath tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and material list need to consist of the following:
Planning for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are practical in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait till the bathtub has been used at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Many thanks for spending some time to browse our content. Are you aware of another person who is involved in the topic? Be sure promote it. Thank you for taking the time to read it.
Top Article Report this page